Fix The Door You Have
A shower door that drags on the curb, drips onto the floor, or has a chip at the corner doesn’t usually need a whole new enclosure. Hinges loosen, sweeps and seals wear out, clips work loose, and all of those are repairable.
Superior Glass installs shower doors and enclosures across the Twin Ports, and the same shop handles the repairs. We figure out why the door is misbehaving, replace the worn parts, and remake the glass only when the glass is the problem.
Small problems grow in a shower. A door that drips a little for a year can soak a subfloor, and a door that drags can chip its own edge. Catching them early keeps the repair small.
When a repair isn’t worth it, we’ll say so and walk you through frameless shower doors instead.
- Sagging and dragging doors realigned
- Worn sweeps and seals replaced
- Leaks traced to the real cause
- Loose clips and clamps reset
- Chipped or broken glass remade to measure

Shower Door Parts, In Plain Terms
Most repairs come down to one of these parts. Here’s what each one does.
Get A Free Estimate| Frameless glass | Usually 3/8 or 1/2 inch tempered glass |
|---|---|
| Framed glass | Thinner tempered glass held in a metal frame |
| Hinges | Wall-to-glass or glass-to-glass, carrying the door’s full weight |
| Sweeps and seals | Vinyl or polycarbonate strips that are wear parts, meant to be replaced |
| Clips and clamps | Hold fixed panels to the wall, curb, and each other |
| Glass rule | Tempered glass can’t be trimmed, drilled, or patched after it’s made |
Matching Glass And Hardware
We bring samples to your consultation. These are the options homeowners pick from most.
Glass
Hardware
The Four Repairs We See Most
Sagging And Dragging Doors
A frameless door is heavy glass hanging on two or three hinges. Over time hinge screws loosen, wall anchors work in the tile, or the hinge itself wears. The door drops, drags on the curb, and stops closing square. We tighten, shim, or replace the hinges and reset the door so it swings clean and closes with an even gap.
- Door drags on the curb or catches the panel
- Latch-side gap wider at the top than the bottom
- Hinge screws that keep working loose

Leaks
Most leaks come from a worn door sweep, a missing side seal, or water sheeting off a panel where there’s no drip rail. Sometimes it’s the layout: a shower head aimed at the door gap, or a door swinging inward and dripping onto the floor.
We run water, watch where it goes, and find where it’s actually getting out before we replace anything. Our leaking shower door guide covers the common causes.

Chips, Cracks, And Broken Glass
Tempered glass is strong across its face and vulnerable at its edges. A chip on the edge weakens the whole panel, and it can break without warning later. Because tempered glass can’t be cut after it’s made, the fix is a new panel measured and made to size, with holes and notches in the right places.
We match thickness and glass type, and we measure the opening again rather than trusting the old panel’s size. Walls and curbs are rarely perfectly plumb, and the new panel has to fit the room you have.

Sliding Doors And Loose Hardware
Sliding and bypass doors run on rollers that wear, and tracks fill with soap and minerals. Handles, towel bars, and clamps loosen with daily use. Worn rollers, guides, and clamps can usually be replaced, and when an exact match isn’t available, replacing hardware as a set keeps the finish consistent.
A loose handle is worth fixing right away. It’s the part everyone grabs, and a handle that rocks puts stress on the glass around its holes.

Repair Or New Enclosure?
An honest look at when to fix and when to start over. We’ll confirm at the visit.
| Repair | New enclosure | |
|---|---|---|
| Makes sense when | Glass is sound, parts are worn | Glass is etched, damaged, or the layout doesn’t work |
| Typical work | Hinges, seals, sweeps, clips, one new panel | New glass, hardware, and layout |
| Look | Stays the same | Chance to change glass and finish |
| Hard water etching | Can’t be reversed | Fresh glass, with an optional protective coating |
| Remodeling soon? | Keeps you going until then | Plan it with the new tile |
Repairs That Hold
Fix The Cause
A new sweep won’t stop a leak caused by a sagging door. We find the real problem first.
Safety Glass Only
Every replacement panel is tempered safety glass, made to measure for your opening.
Floors Protected
Promise Plan: we protect your bathroom, clean up after ourselves, and fix anything that isn’t right.
On Time
Also Promise Plan: we show up when we say we will, because your bathroom is out of service until we do.
Measured Again
Replacement panels are measured to the opening, not copied from the broken glass.
Local Since 1933
The same Superior shop that installs shower glass across the Twin Ports.
What Affects The Price
Every shower door repair is priced after we see it. These are the things that move it.
Parts Or Glass
Seals and sweeps are simple. A new tempered panel is a bigger job.
Glass Thickness
3/8 or 1/2 inch frameless glass, or thinner framed glass.
Hardware Match
Standard parts versus finishes or styles that are hard to match.
Wall Condition
Loose anchors or damaged tile behind a hinge need attention first.
Glass Type
Clear, low-iron, frosted, or textured glass in a replacement panel.
Coating
Adding an easy-clean protective coating to new glass.
How A Superior Glass Job Runs
Measure On Site
Free consultation at your home or business. We measure every opening ourselves.
Template The Opening
Walls are rarely square. We template so the glass fits the room you actually have.
Cut And Fabricate
Glass is cut, edged, and prepared to your template before install day.
Install
Floors protected, glass set, hardware tuned, and the site cleaned up.
Walkthrough
We check every door, seal, and edge with you, then show you how to care for it.
Recent Shower Glass Jobs




Every photo here is a real Superior Glass job, from the company’s own project posts.
Frequently Asked Questions
Usually the hinges have loosened or the wall anchors have shifted, so the door has dropped. Sometimes the hinge cam or pivot has worn. Tightening and realigning often fixes it; worn hinges get replaced.
It depends on water hardness and cleaning products. Sweeps and seals are wear parts. When they turn cloudy, stiff, cracked, or stop touching the glass and curb, they’re due.
No. Shower glass is tempered, and tempered glass can’t be cut, drilled, or edged after it’s made without shattering. A change in size means a new panel made to measure.
Tempered glass can break without an obvious cause, usually from old edge damage, a hard knock earlier, stress from misaligned hardware, or, rarely, a tiny nickel sulfide inclusion in the glass. When it breaks it crumbles into small pieces, which is the safety feature. Keep people out of the room and call us.
Surface deposits usually can. Etching, where minerals have actually eaten into the glass, can’t be reversed. See hard water stains on shower glass and our page on protective glass coatings.
We don’t recommend it. A chip on the edge of tempered glass weakens the whole panel, and it can break later with no warning. Keep the door closed gently, keep kids out of the shower, and have the panel replaced.
Call us about your door, whoever installed it, and we’ll tell you plainly whether we can help. Some hardware is easier to match than others, and we’ll say up front if a part is hard to source.
Get Your Shower Door Working Again
Call (715) 685-0500 or send the form. Tell us what the door is doing, and we’ll tell you what it takes and put the price in writing.
